The routine is this: skim the surface, shut the water off, drain or tip the trough right out, scrub the floor and sides with a stiff brush, flush the loosened sediment away, then refill and check the float. Agriculture Victoria says troughs in a stock containment area should be completely emptied, cleaned and refilled every 1 to 2 days, and that surface material should be skimmed off the water daily. The steps below are that guidance turned into a routine you can repeat in the same order every time.
What to take with you
A stiff brush with a handle long enough to reach right across the trough, a scoop or bucket if the trough has no outlet, and a shifter for the outlet bung or stand pipe.
The routine, step by step
- Skim first. Agriculture Victoria lists dust or straw floating on the surface among the things stock avoid, so lift it off before you stir the water up and it leaves with the first lot of water.
- Isolate the water. Close the gate valve or tap so the float valve is not refilling the trough while you work.
- Open the outlet, or tip it out. The MLA feedlot design manual describes the stand pipe being unscrewed for trough draining and cleaning. With no outlet, tip or bail it, leaving a little water to scrub with.
- Scrub the floor, the sides and the ends. The manual notes that troughs are cleaned by flushing out the existing water and then adding more during scrubbing, so a brush and a bit of water does the job. Ends and corners are where sediment collects.
- Flush the dirty water away. Rinse until the water runs clear. The manual makes the same point for the drain lines, recommending additional flushing time to completely remove any sediment. Tipping by hand, a second rinse does the job.
- Check the float valve and its cover. Covers have to be easily removable for access to float and gate valves. Agriculture Victoria wants the level kept close to full at all times, and the float valve fully protected with a durable, stock-proof cover.
- Refill and watch the water come in. Water that is warm or stagnant, or polluted with food residues, is water stock reduce their intake of.
- Clean around the outside too. Manure accumulating under and around a trough makes the next clean harder, which is why the manual calls for enclosed trough sides and a concrete apron at least 3 m wide.
How long it takes
Our calculator uses ten minutes per trough per clean, including getting there. Once a day, that is about 61 hours a year for one trough, and at labour valued at $35 an hour, about $2,123 a year. In summer it can be twice a day. On a Victorian dairy farm where we have a trial trough, troughs are cleaned every day, and twice a day in hot weather because algae grows within 24 hours.
What changes with a drain outlet
Most of the ten minutes is tipping and bailing, so an outlet is the biggest single change you can make. Agriculture Victoria is plain about it: a long shallow trough with a smooth internal profile, a gate valve and a large outlet bung will make cleaning quick and efficient. The MLA manual adds that the outlet should sit so water flows away from the trough, preferably to a drain, and that underground pipework needs good slope, above 1%, and no sharp bends, because stones, grain and other debris will clog it.
Two other design points save time. Rectangular troughs are more easily cleaned internally than circular ones. And a concrete trough gets harder to clean as the surface deteriorates, so a fibreglass or polyethylene insert, or an epoxy resin coating applied when the trough is new, keeps the floor smooth.
What changes with a flushing trough
With the SATURN trough the flush replaces steps 2 to 5. At the interval you set from your phone, the flush valve opens, water runs along the trough floor and carries sediment and feed residue out through the drain, and the mechanical float valve refills the trough with clean water. The manufacturer suggests one to two flushes a day depending on stock numbers, using about 60 litres per flush (both manufacturer figures). The trough holds 50 litres, so there is less to move each time. What it does not replace is checking: the float, the drain and the water still want a look.
What we recommend
Set the routine above in a fixed order and do your worst trough first, because that is where the minutes are. Put your own cleans per week, minutes per clean and labour rate into the calculator before you spend anything. Then test a flushing trough on your own farm for 3 months against those figures, recording cleans, minutes and faults each week.
- Agriculture Victoria, Water supply in stock containment areas (agriculture.vic.gov.au)
- Meat & Livestock Australia, Feedlot design manual, chapter 20 Water trough design and sewer systems (2016)
- Manufacturer information, SATURN trough specifications (cleantrough.com.au/product)